keyboard_arrow_left Back to the overview

Install LineageOS on
Motorola moto g (2015)

osprey

Basic requirements

  1. Read through the instructions at least once before actually following them, so as to avoid any problems due to any missed steps!
  2. Make sure your computer has adb and fastboot. Setup instructions can be found here.
  3. Enable USB debugging on your device.
  4. Make sure that your model is actually listed in the “Supported models” section here (exact match required!)
  5. Boot your device with the stock OS at least once and check every functionality.
  6. LineageOS is provided as-is with no warranty. While we attempt to verify everything works you are installing this at your own risk!

Checking the correct firmware

Installation on your device requires a specific firmware version to be installed before you continue.

  • Firmware refers to a device-specific set of images that are included in, and updated by the stock OS
  • LineageOS builds for this device require an Android 6.0.1 version of the stock OS to be installed prior to following the installation guide
  • Please ensure that you are checking the Android version, and not the vendor OS version
  • Being on another custom ROM, including unofficial builds of the same version of LineageOS, does not ensure that this requirement has been fulfilled
  • Please re-read this section as many times as necessary to fully understand the requirements

Failing to install the correct firmware version prior to installation may result in failure to install LineageOS, unexpected crashes post-installation, or permanent damage to your device!

Unlocking the bootloader

  1. Connect the device to your PC via USB.
  2. On the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type:
    adb -d reboot bootloader
    

    You can also boot into fastboot mode via a key combination:

    • With the device powered off, hold Volume Down + Power. On the next screen use Volume Down and Volume Up to scroll and then press Power to select.
  3. Once the device is in fastboot mode, verify your PC finds it by typing:
    fastboot devices
    

    If you don’t get any output or an error:

    • on Windows: make sure the device appears in the device manager without a triangle. Try other drivers until the command above works!
    • on Linux or macOS: If you see no permissions fastboot try running fastboot as root. When the output is empty, check your USB cable and port!
  4. Follow the instructions at Motorola Support to unlock your bootloader.

  5. Since the device resets completely, you will need to re-enable USB debugging to continue.

Installing Lineage Recovery using fastboot

  1. Build a LineageOS installation package. The recovery will be built as part of it!
  2. Connect your device to your PC via USB if it isn’t already.
  3. If your device isn’t already in fastboot mode, on the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type:
    adb -d reboot bootloader
    

    You can also boot into fastboot mode via a key combination:

    • With the device powered off, hold Volume Down + Power. On the next screen use Volume Down and Volume Up to scroll and then press Power to select.
  4. Once the device is in fastboot mode, verify your PC finds it by typing:
    fastboot devices
    

    If you don’t get any output or an error:

    • on Windows: make sure the device appears in the device manager without a triangle. Try other drivers until the command above works!
    • on Linux or macOS: If you see no permissions fastboot try running fastboot as root. When the output is empty, check your USB cable (preferably use a USB Type-A 2.0 one or a USB hub) and port!
  5. Flash recovery onto your device:
    fastboot flash recovery recovery.img
    
  6. Now reboot into recovery to verify the installation.
    • Use the menu to navigate to and to select the Recovery option.

Installing LineageOS from recovery

  1. Build a LineageOS installation package.
  2. If you are not in recovery, reboot into recovery:
    • With the device powered off, hold Volume Down + Power. On the next screen use Volume Down to scroll to recovery and then press Power to select.
  3. Now tap Factory Reset, then Format data / factory reset and continue with the formatting process. This will remove encryption and delete all files stored in the internal storage, as well as format your cache partition (if you have one).
  4. Return to the main menu.
  5. Sideload the LineageOS .zip package but do not reboot before you read/followed the rest of the instructions!
    • On the device, select “Apply Update”, then “Apply from ADB” to begin sideload.
    • On the host machine, sideload the package using: adb -d sideload filename.zip.

Installing Add-Ons

  1. Click Apply Update, then Apply from ADB, then adb -d sideload filename.zip for all desired packages in sequence.
    When presented with a screen that says Signature verification failed, click Yes. It is expected as add-ons aren’t signed with LineageOS’s official key!

All set!

Once you have installed everything successfully, you can now reboot your device into the OS for the first time!

  • Click the back arrow in the top left of the screen, then “Reboot system now”.

Get assistance

After you’ve double checked that you followed the steps precisely, didn’t skip any and still have questions or got stuck, feel free to ask on our subreddit or in #LineageOS on Libera.Chat.