keyboard_arrow_left Back to the overview

Install LineageOS on
Motorola moto z (2018)

nash

Basic requirements

  1. Read through the instructions at least once before actually following them, so as to avoid any problems due to any missed steps!
  2. Make sure your computer has adb and fastboot. Setup instructions can be found here.
  3. Enable USB debugging on your device.
  4. Make sure that your model is actually listed in the “Supported models” section here (exact match required!)
  5. Boot your device with the stock OS at least once and check every functionality.
  6. LineageOS is provided as-is with no warranty. While we attempt to verify everything works you are installing this at your own risk!

Firmware Requirements

Before following these instructions please ensure that the device is on the latest firmware available for your variant. To discern this, run the command adb -d shell getprop ro.boot.hardware.sku. Please refer to the table below to discern what the latest firmware for your variant is:

Variant Version
XT1789-02/03/04 8.0
XT1789-05/06/07 9.0

If the device’s firmware version doesn’t match the version required above, please go into “Settings”, “System”, “System Updates”, click “Check for Updates”, and apply any available. You may need to do this multiple times.

Unlocking the bootloader

  1. Connect the device to your PC via USB.
  2. On the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type:
    adb -d reboot bootloader
    

    You can also boot into fastboot mode via a key combination:

    • With the device powered off, hold Volume Down + Power.
  3. Once the device is in fastboot mode, verify your PC finds it by typing:
    fastboot devices
    

    If you don’t get any output or an error:

    • on Windows: make sure the device appears in the device manager without a triangle. Try other drivers until the command above works!
    • on Linux or macOS: If you see no permissions fastboot try running fastboot as root. When the output is empty, check your USB cable and port!
  4. Follow the instructions at Motorola Support to unlock your bootloader.

  5. Since the device resets completely, you will need to re-enable USB debugging to continue.

Installing Lineage Recovery using fastboot

  1. Download Lineage Recovery. Simply download the latest recovery file, named boot.img.
  2. Connect your device to your PC via USB if it isn’t already.
  3. If your device isn’t already in fastboot mode, on the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type:
    adb -d reboot bootloader
    

    You can also boot into fastboot mode via a key combination:

    • With the device powered off, hold Volume Down + Power.
  4. Once the device is in fastboot mode, verify your PC finds it by typing:
    fastboot devices
    

    If you don’t get any output or an error:

    • on Windows: make sure the device appears in the device manager without a triangle. Try other drivers until the command above works!
    • on Linux or macOS: If you see no permissions fastboot try running fastboot as root. When the output is empty, check your USB cable (preferably use a USB Type-A 2.0 one or a USB hub) and port!
  5. Flash recovery onto your device:
    fastboot flash boot boot.img
    
  6. Now reboot into recovery to verify the installation. Do not reboot into the existing OS, since it will overwrite the recovery you just installed!
    • With the device powered off, hold Volume Down + Power.

Ensuring all firmware partitions are consistent

In some cases, the inactive slot can be unpopulated or contain much older firmware than the active slot, leading to various issues including a potential hard-brick. We can ensure none of that will happen by copying the contents of the active slot to the inactive slot.

To do this, sideload the copy-partitions-20220613-signed.zip package by doing the following:

  1. Download the copy-partitions-20220613-signed.zip file from here.
  2. Sideload the copy-partitions-20220613-signed.zip package:
    • On the device, select “Apply Update”, then “Apply from ADB” to begin sideload.
    • On the host machine, sideload the package using: adb -d sideload copy-partitions-20220613-signed.zip
  3. Now reboot to recovery by tapping “Advanced”, then “Reboot to recovery”.

Installing LineageOS from recovery

  1. Download the LineageOS zip file that you would like to install or build the package yourself.
  2. If you are not in recovery, reboot into recovery:
    • With the device powered off, hold Volume Down + Power.
  3. Now tap Factory Reset, then Format data / factory reset and continue with the formatting process. This will remove encryption and delete all files stored in the internal storage, as well as format your cache partition (if you have one).
  4. Return to the main menu.
  5. Sideload the LineageOS .zip package but do not reboot before you read/followed the rest of the instructions!
    • On the device, select “Apply Update”, then “Apply from ADB” to begin sideload.
    • On the host machine, sideload the package using: adb -d sideload filename.zip.

Installing Add-Ons

  1. Click Apply Update, then Apply from ADB, then adb -d sideload filename.zip for all desired packages in sequence.
    When presented with a screen that says Signature verification failed, click Yes. It is expected as add-ons aren’t signed with LineageOS’s official key!

All set!

Once you have installed everything successfully, you can now reboot your device into the OS for the first time!

  • Click the back arrow in the top left of the screen, then “Reboot system now”.

Get assistance

After you’ve double checked that you followed the steps precisely, didn’t skip any and still have questions or got stuck, feel free to ask on our subreddit or in #LineageOS on Libera.Chat.