Install LineageOS on
Nokia 6.1 Plus
DRG
Do not continue after something fails!
Basic requirements
- Read through the instructions at least once before actually following them, so as to avoid any problems due to any missed steps!
- Make sure your computer has
adb
andfastboot
. Setup instructions can be found here. - Enable USB debugging on your device.
- Make sure that your model is actually listed in the “Supported models” section here (exact match required!)
- Boot your device with the stock OS at least once and check every functionality.
Warning: Make sure that you can send and receive SMS and place and receive calls (also via WiFi and LTE, if available), otherwise it won’t work on LineageOS either! Additionally, some devices require that VoLTE/VoWiFi be utilized once on stock to provision IMS.
- LineageOS is provided as-is with no warranty. While we attempt to verify everything works you are installing this at your own risk!
Pre-Install Notice
Unofficial bootloader unlocks for this device tend to leave the device in a strange state. This can cause a false data-corruption notice when updating LineageOS via the built-in Updater app.
To mitigate this issue, reflash the latest stock firmware for your model before starting.
Unlocking the bootloader
Installing Lineage Recovery using fastboot
- Build a LineageOS installation package. The recovery will be built as part of it!
Important: Other recoveries may not work for installation or updates. We strongly recommend to use the one linked above!
- Connect your device to your PC via USB if it isn’t already.
- If your device isn’t already in fastboot mode, on the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type:
adb -d reboot bootloader
You can also boot into fastboot mode via a key combination:
- With the device powered off and plugged into USB port, hold Volume Down + Power.
- Once the device is in fastboot mode, verify your PC finds it by typing:
fastboot devices
If you don’t get any output or an error:
- on Windows: make sure the device appears in the device manager without a triangle. Try other drivers until the command above works!
- on Linux or macOS: If you see
no permissions fastboot
try runningfastboot
as root. When the output is empty, check your USB cable (preferably use a USB Type-A 2.0 one or a USB hub) and port!
Tip: Some devices have buggy USB support while in bootloader mode, if you seefastboot
hanging with no output when using commands such asfastboot getvar ...
,fastboot boot ...
,fastboot flash ...
you may want to try a different USB port (preferably a USB Type-A 2.0 one) or a USB hub. - Flash recovery onto your device:
fastboot flash boot boot.img
- Now reboot into recovery to verify the installation.
Do not reboot into the existing OS, since it will overwrite the recovery you just installed!
-
With the device powered off and plugged into USB port, hold Volume Up + Power. Keep holding both buttons until the “Android One” logo appears on the screen, then release Power but keep holding Volume Up.
Note: If you can’t power down the device, try long-pressing the key-combination (if any was used in the instructions above) until the device reboots and follow the instructions above
Note: If your recovery does not show the LineageOS logo , you accidentally booted into the wrong recovery. Please start at the top of this section! -
Installing LineageOS from recovery
- Build a LineageOS installation package.
- If you are not in recovery, reboot into recovery:
- With the device powered off and plugged into USB port, hold Volume Up + Power. Keep holding both buttons until the “Android One” logo appears on the screen, then release Power but keep holding Volume Up.
- Now tap Factory Reset, then Format data / factory reset and continue with the formatting process. This will remove encryption and delete all files stored in the internal storage, as well as format your cache partition (if you have one).
- Return to the main menu.
- Sideload the LineageOS
.zip
package but do not reboot before you read/followed the rest of the instructions!- On the device, select “Apply Update”, then “Apply from ADB” to begin sideload.
- On the host machine, sideload the package using:
adb -d sideload filename.zip
.Tip: After the package is installed, recovery will inform you that reboot to recovery is required to install add-ons. In case you want to do that, please select “Yes,” otherwise “No”.Tip: Normally, adb will reportTotal xfer: 1.00x
, but in some cases, even if the process succeeds the output will stop at 47% and reportadb: failed to read command: Success
. In some cases it will reportadb: failed to read command: No error
oradb: failed to read command: Undefined error: 0
which is also fine.
Installing Add-Ons
arm64
architecture), you can download it from here.
This add-on needs to be installed before booting into LineageOS for the first time!- Click
Apply Update
, thenApply from ADB
, thenadb -d sideload filename.zip
for all desired packages in sequence.
When presented with a screen that saysSignature verification failed
, clickYes
. It is expected as add-ons aren’t signed with LineageOS’s official key!
All set!
Once you have installed everything successfully, you can now reboot your device into the OS for the first time!
- Click the back arrow in the top left of the screen, then “Reboot system now”.
Get assistance
After you’ve double checked that you followed the steps precisely, didn’t skip any and still have questions or got stuck, feel free to ask on our subreddit or in #LineageOS on Libera.Chat.